Back to all

How Much is Enough for Huntersville Auto Owners? Tire Tread Depth

February 22, 2016

Most Huntersville drivers know that tires wear out and that the wear has to do with tread depth. Most of us have heard that “bald” tires are dangerous, but most of us picture a tire with no tread at all when we think of a bald tire. And when we take our vehicles in for preventive maintenance, the technician tells us they're need to be replaced long before all the tread is worn off. Just how much tire tread wear is too much? And how can you tell? Tires are and their condition is important to the safe handling of a vehicle, so it's for Huntersville vehicle owners to know the answers to these questions.

First of all, it's important to understand that there may be a legal limit to tread wear. If your tires are worn past this limit, you have to replace them to be in compliance with North Carolina auto safety laws. That's why measuring your tread wear is part of a vehicle safety inspection.

In some jurisdictions, tread must be at least 1.6 millimeters or 2/32 of an inch thick. This standard has been in effect since 1968. But this standard has recently been called into question, and some North Carolina professionals are arguing that it be changed.

The safety issue that has brought this standard under scrutiny is the ability of a vehicle to stop on a wet surface. When a vehicle has trouble stopping, most Huntersville drivers immediately look at the brakes as the source of the problem. But tires are crucial to safe stopping distances because they provide the traction required in a stop.

A tire's contact with the road surface creates traction, which allows for effective braking. On a wet surface, a tire only has traction if it can get to the road's surface. So tire tread is designed to channel water out from under the tire to allow it to stay in contact with the road. If the tire can't shift the water, then it starts to “float.” This condition is called hydroplaning. It is very dangerous for Huntersville drivers since the vehicle won't stop no matter how hard the driver presses the brakes. Steering control is also lost.

A recent study tested the stopping ability of a passenger car and a full-sized pick-up on a road surface covered with only a dime's depth of water (less than a millimeter). The vehicles were traveling at 70 mph (112 kph) when they stopped on the wet surface. At 2/32 (1.6 mm) tread depth, the stopping distance was double that of a new tire. The passenger car was still traveling at 55 mph (89 kph) when it reached the stopping distance it experienced with new tires.

Let's suppose that you're on a busy Huntersville road in a light drizzle and a vehicle stops suddenly in front of you. You just bought new tires and you brake hard, missing the vehicle with only inches to spare. If you hadn't bought those new tires, you would have crashed into that vehicle at 55 mph (89 kph). That is a major difference.

What if your tires had a tread depth of 4/32 (3.2 mm)? You would have crashed into that vehicle at 45 mph (72 kph). Still not a good situation. But it's better.

Now what if you were driving that pick-up truck? You wouldn't have missed that vehicle in the first place, and you would have crashed at higher rates of speed in both of the other scenarios. The heavier your vehicle, the longer its stopping distance. It's a matter of physics.

The results of this test has led Consumer Reports and others to ask that the standard for tread wear be changed from 2/32 (1.6 mm) to 4/32 (3.2 mm). The increased standard will improve safety on the road and save lives here in North Carolina and nationally.

Of course, until the standard changes, you'll have to decide whether you'll be willing to replace your tires a little sooner.

You can use an American quarter to tell if your tread wear is down to 4/32 (3.2 mm). Place the quarter into the tread with George's head toward the tire and his neck toward you. If the tread doesn't cover George's hairline, you're under 4/32 (3.2 mm). With a Canadian quarter, the tread should cover the digits of the year.

You can measure the 2/32 inch (1.6 mm) tread wear with a penny. If the tread touches the top of Abe's head, it's at 2/32 (1.6 mm). Tires are super important when it comes to vehicle care. But their condition has a major impact on safety. We need to decide whether to sacrifice safety for economy. Keeping our tread wear above 4/32 in (3.2 mm) is good auto advice.

Tuffy Tire & Auto Huntersville
16925 Caldwell Creek Dr
Huntersville, North Carolina 28078
704-895-5586
tuffy-tire-auto-huntersville.autotipsblog.com

Need Service?

Request a Quote

More articles from Tuffy Huntersville

What to Do After You Buy a Used Vehicle in Huntersville

September 13, 2022

So you've bought a used vehicle in the Huntersville area. Do you know what you're getting? It is hard to know what you're getting because people in the Huntersville area sell vehicles for different reasons. Think about why you've sold vehicles. Did you just want something new or were there probl... More

Braking News: Keep Your Stopping Power

September 12, 2022

Richard Petty once told AutoNetTV, You've gotta have good brakes. If you've got good brakes you can keep yourself out of a lotta trouble.That's why a regular brake inspection is on every Huntersville driver's maintenance schedule. An inspection by your service advisor at Tuffy Tire & Auto Hunter... More

Trip Inspection at Tuffy Tire & Auto Huntersville in Huntersville

September 11, 2022

Huntersville area drivers love their vehicles. And one of the most enjoyable things about them is taking a road trip. Freedom from daily schedules, new sights and the open road it's great! But there's nothing like vehicle trouble to bring the fun to a grinding halt.Now Huntersville drivers can'... More

gtag('config', 'AW-875953767'); gtag('config', 'UA-51268202-1'); gtag('config', 'G-Q5KNRMVSLQ');